View KB15CKW01-12-FF_7515714.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

series kb miniature pushbuttons www.nkk.com d22 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles general specifcations electrical capacity (resistive load) power level (silver): 1a @ 125/250v ac or 1a @ 30v dc logic level (gold): 0.4va maximum @ 28v ac/dc maximum (applicable range 0.1ma ~ 0.1a @ 20mv ~ 28v) note: find additional explanation of operating range in supplement section. other ratings contact resistance: 50 milliohms maximum insulation resistance: 1,000 megohms minimum @ 500v dc dielectric strength: for silver: 1,000v ac minimum between contacts for 1 minute minimum & 1,500v ac minimum between contacts & case for 1 minute minimum; for gold: 750v ac minimum between contacts for 1 minute minimum & 1,500v ac minimum between contacts & case for 1 minute minimum mechanical life: 100,000 operations minimum electrical life: 50,000 operations minimum for silver; 100,000 operations minimum for gold nominal operating force: single pole 0.98 ~ 2.45n for maintained & 0.98 ~ 1.96n for momentary; double pole 1.47 ~ 3.43n for maintained & 1.47 ~ 2.94n for momentary contact timing: nonshorting (break-before-make) travel: pretravel .087 (2.2mm); overtravel .031 (0.8mm); total travel .118 (3.0mm) materials & finishes housing: polyamide (ul94v-0) movable contactor: silver for power circuit; copper with gold plating for logic level circuit stationary contacts: silver for power circuit; copper with gold plating for logic level circuit housing base: polyamide (ul94v-0) terminal base: polyester common terminals: phosphor bronze with silver fash plating for power circuit; phosphor bronze with gold fash plating for logic level circuit end terminals: brass with silver fash plating for power circuit; brass with gold fash plating for logic level circuit lamp terminals: phosphor bronze with nickel fash plating environmental data operating temperature range: C25c through +50c (C13f through +122f) for illuminated C25c through +70c (C13f through +158f) for nonilluminated humidity: 90 ~ 95% humidity for 96 hours @ 40c (104f) vibration: 10 ~ 55hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours shock: 50g (490m/s 2 ) acceleration (tested in 6 right angled directions, with 3 shocks in each direction) installation mounting torque: 0.78nm (6.9 lb ? in) maximum cap installation force: 4.51n (1.0 lbf) maximum downward force on cap soldering time & temperature: manual soldering: see profle a in supplement section. standards & certifcations flammability standards: ul94v-0 housing & housing base ul: file no. e44145 - recognized only when ordered with marking on switch. add /u or /cul before frst dash in part number to order ul recognized switch. single & double pole models recognized at 1a @ 125/250v ac, 1a @ 30v dc, & 0.4va @ 28v dc. csa: file no. 023535_0_000 - certifed only when ordered with marking on switch. add /c before frst dash in part number to order csa certifed switch. single & double pole models recognized at 1a @ 125/250v ac, 1a @ 30v dc, & 0.4va @ 28v dc.
series kb miniature pushbuttons www.nkk.com d23 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt distinctive characteristics bright illumination with numerous color variations. spot illumination available. square, rectangular, and round shaped caps. front panel relamping. choice of bright or super bright leds in red, amber, green, white, and blue. latchdown feature gives indication of circuit status. audible and tactile feedback with smooth and responsive operation. snap-action mechanism for long life. stainless steel frame on snap-in models has a specially designed projection, which prevents rotation and correctly orients switch in panel. 12mm body diameter. molded-in terminals lock out fux, dust, and other contaminants. 8mm panel thickness capability. rear panel bushing or snap-in mounting. optional pcb adaptors in straight and right angle types. matching indicators available. actual size
housing k black only shapes bushing mounting s square c round r rectangular snap-in mounting k square m round n rectangular poles 1 spdt 2 dpdt 1 c k w01 kb solid cap with green lens and green filter black housing silver contacts and solder lug terminals; rated 1a @ 125/250v ac 12-volt incandescent lamp round with bushing mounting spdt on-(on) circuit circuits 5 on (on) ( ) = momentary 6 on on alternate action with latchdown contacts & terminals w01 silver contacts and solder lug terminals * 1a @ 125/250v ac g01 gold contacts and solder lug terminals * 0.4va @ 28v ac/dc 5 description for typical ordering example KB15CKW01-12-FF typical switch ordering example solid cap: lens/filter colors a black/none (nonilluminated only. available in square and round only.) bb white/white fb green/white cb red/white ff green/green cc red/red gb blue/white eb yellow/white gg blue/blue 12 incandescent lamp used with solid cap 05 5-volt 12 12-volt no code nonilluminated ff incandescent or neon used with insert cap 05 5-volt 12 12-volt 01 110-volt neon no code nonilluminated led cap: lens/diffuser colors ab square spot illuminated black cap/white window jb clear/white jc clear/red jd clear/amber jf clear/green led cap: lens/diffuser colors jb clear/white super bright led used with cap for led 6b white 6f green 6g blue bright led used with cap for led colors resistor no code no resistor 05 5-volt 12 12-volt 24 24-volt 5c red 5d amber 5f green insert cap: lens/filter colors jb clear/white jc clear/red je clear/yellow * jf clear/green * jg clear/blue * jf & jg not suitable with neon. barrier type no code no barrier b with barrier lamps cap types & colors * wire harness & cable assemblies offered only in americas important: switches are supplied without ul, culus & csa marking unless specifed. ul, culus & csa recognized only when ordered with marking on the switch. specifc models, ratings, & ordering in- structions are noted on general specif- cations page. www.nkk.com d25 series kb miniature pushbuttons www.nkk.com d24 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt
series kb miniature pushbuttons www.nkk.com d26 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles mounting types & shapes plunger position ( ) = momentary connected terminals throw & switch/lamp schematics pole model normal down normal down notes: switch is marked with + and C. lamp circuit is isolated and requires external power source. sp kb15 *kb16 on on (on) on 2-3 2-1 spdt dp kb25 *kb26 on on (on) on 2-3 5-6 2-1 5-4 dpdt bushing mounting s .551 (14.0mm) square bezel or barrier is an integral part of the switch body. one mounting nut at057 supplied with each switch. snap-in mounting r * when in latchdown position for the alternate circuit, cap position is .055 (1.4mm) above the built-in bezel. poles & circuits 4 6 1 3 25 (com) l (+) (-) l l (+) (-) l 2 (com) 1 3 c bezel or barrier is an integral part of the switch body. .551 (14.0mm) round .551 x .728 (14.0mm x 18.5mm) rectangular k .551 (14.0mm) square n m .551 (14.0mm) round .551 x .728 (14.0mm x 18.5mm) rectangular housing k housing available in black only. bezel or barrier is an integral part of the switch body. panel cutouts bushing mounting snap-in mounting panel thicknesses, when using optional accessories, are shown with the accessories at the end of this kb section. without keyway with keyway panel thickness: .020 ~ .315 (0.5 ~ 8.0mm) panel thickness: .039 ~ .138 (1.0 ~ 3.5mm) (12.3) dia .484 (12.3) dia .484 (1.2) r .047 (6.8) .268 no barrier with barrier no barrier with barrier no barrier with barrier no barrier with barrier (12.3) dia .484 (4.9) .193
series kb miniature pushbuttons www.nkk.com d27 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt contact materials, ratings & terminals silver contacts gold contacts complete explanation of operating range in supplement section. w g lamp colors & specifications the electrical specifcations shown are determined at a basic temperature of 25c. led circuit is isolated and requires external power source. polarity marks are on the bottom of the switch. if the source voltage exceeds the rated voltage, a ballast resistor is required. the resistor value can be calculated by using the formula in the supplement section. ambient temperature range for lamps below: C25c ~ +50c. power level 1a @ 125v ac & 250v ac logic level 0.4v a maximum @ 28v ac/dc 01 solder lug (5.0) .197 (1.8) .071 (1.0) .039 (2.0) .079 thk = (0.2) .008 com = (0.1) .005 a partitioned plastic guard is supplied with each switch to provide insulation between terminals. installation steps: 1. identify wire-to-ter minal connections. 3. solder the connections. 2. thread wires through the guard. 4. push the guard fully onto the switch body . (17.0) .669 (14.0) dia .551 (12.4) dia .488 voltage v 5v ac 12v ac 110v ac current i 115ma 60ma 1.5ma endurance hours 7,000 average 10,000 05 12 01 recommended resistors for neon: 33k ohms for 110v ac; 100k ohms for 220v ac t-1 bi-pin at611 incandescent at615 neon incandescent & neon lamps resistor codes color codes: forward peak current i fm typical forward current i f 25ma 20ma 10ma forward voltage v f 5v 12v 24v reverse peak voltage v rm 4v 8v 16v current reduction rate above 25c ?i f 5c 5d 5f 12 24 05 red amber green at634 leds are colored in off state. t-1 1 ? 4 bi-pin bright led with resistor (-) (+) (+) (-) (+) (-) at634 5-volt 2-element with 1 resistor at634 12-volt 4-element with 2 resistors at634 24-volt 4-element with 2 resistors barrier type no code no barrier built-in bezel b with barrier built-in barrier only available for square and rectangular no code no lamp at055 crossover guard
series kb miniature pushbuttons www.nkk.com d28 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles lamp colors & specifications color white green blue forward peak current i fm 30ma 30ma 30ma typical forward current i f 20ma 20ma 20ma forward voltage v f 3.6v 3.5v 3.6v reverse peak voltage v rm 5v 5v 5v current reduction rate above 25c ?i f 0.50ma/c 0.50ma/c 0.50ma/c ambient temperature range C25 ~ +50c 6f 6g 6b at625g blue at631b white at632f green t-1 bi-pin super bright single element led (+) (-) cap types & color combinations bb solid cap for incandescent lamp & nonilluminated lens/filter colors available: cb cc eb at485 square jf and jg not suitable with neon lamp. fb ff gb gg color codes: a black b white c red e yellow f green g blue j clear material: polycarbonate finish: glossy at486 round at4021 rectangular material: polycarbonate finish: glossy (11.6) sq .457 (6.2) .244 (4.5) .177 (11.6) dia .457 (6.2) .244 (4.5) .177 (11.6) sq .457 (6.2) .244 (4.5) .177 (11.6) dia .457 (6.2) .244 (4.5) .177 at487 square at488 round at4022 rectangular insert cap for incandescent or neon lamp & nonilluminated jb jc je jf jg lens/filter colors available: (6.3) .248 (4.5) .177 (16.1) .634 (11.6) .457 (11.6) .457 (6.3) .248 (4.5) .177 (16.1) .634 translucent colored lens translucent colored filter lamp at611 transparent clear lens translucent colored filter lamp at611 lamp at615 color codes red amber green forward peak current i fm 30ma 30ma 30ma typical forward current i f 20ma 20ma 20ma forward voltage v f 1.9v 2.0v 2.1v reverse peak voltage v rm 5v 5v 5v current reduction rate above 25c ?i f 0.42ma/c ambient temperature range C25 ~ +50c 5c 5d 5f no code red amber green no resistor (+) (-) t-1 1 ? 2 bi-pin at635 leds are colored in off state. bright led without resistor a ttention electrostatic sensitive devices a nonilluminated only; square & round only
series kb miniature pushbuttons www.nkk.com d29 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt cap for bright led without resistor or led with resistor lens/diffuser colors available: (at4133, 4132, 4134 white diffusers; at4158, 4160, 4159 colored diffusers) square material: polycarbonate finish: glossy round rectangular material: polycarbonate finish: glossy (11.6) sq .457 (6.2) .244 (4.5) .177 (11.6) dia .457 (6.2) .244 (4.5) .177 at4133 square at4132 round at4134 rectangular cap for super bright led jb lens/diffuser colors available: (11.6) .457 (6.3) .248 (4.5) .177 (16.1) .634 transparent clear lens translucent diffuser translucent clear lens translucent white diffuser cap types & color combinations color codes: a black b white c red d amber e yellow f green g blue j clear spot illuminated cap for bright led without resistor or with resistor opaque black cap with translucent white window for spot illumination ab cap/window colors available: at4051 square material: polycarbonate finish: matte bright led at635 bright led at634 (3.0) .118 (1.8) .071 (5.0) .197 (11.6) sq .457 (4.6) .181 (6.2) .244 jb jc jd jf at4133 at4132 at4134 at4158 at4160 at4159 bright led at635 bright led at634 (11.6) .457 (6.3) .248 (4.5) .177 (16.1) .634 (11.6) dia .457 (6.2) .244 (4.5) .177 (11.6) sq .457 (6.2) .244 (4.5) .177 super bright leds at625 at631 at632
series kb miniature pushbuttons www.nkk.com d30 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles typical switch dimensions square ? bushing mount single & double pole rectangular ? bushing mount single & double pole round ? bushing mount single & double pole kb15skw01-05-gg single pole models do not have terminals 4, 5, & 6. kb25ckw01-05-gg single pole models do not have terminals 4, 5, & 6. kb15rkw01-05-gg single pole models do not have terminals 4, 5, & 6. (11.6) sq .457 (14.0) sq .551 (5.0) .197 (1.0) .039 (14.2) .559 (24.7) .972 (5.3) .209 (5.0) .197 m12 p1 (1.0) x (2.0) ty p .039 x .079 (0.2) ty p .008 (1.8) ty p .071 (3.5) .138 latchdown position (1.4) .055 63 52 1 4 l l com (4.9) .193 (1.8) .071 keyway (.127) .005 (5.08) .200 (9.0) .354 (1.7) ty p .067 (11.6) dia .457 (14.0) dia .551 (5.0) .197 (1.0) .039 (14.2) .559 (24.7) .972 (5.3) .209 (5.0) .197 m12 p1 (1.0) x (2.0) ty p .039 x .079 (0.2) ty p .008 (1.8) ty p .071 (3.5) .138 latchdown position (1.4) .055 63 52 1 4 l l com (4.9) .193 (1.8) .071 keyway (.127) .005 (5.08) .200 (9.0) .354 (1.7) ty p .067 (11.6) .457 (16.1) .634 (18.5) .728 (14.0) .551 (5.0) .197 (1.0) .039 (14.2) .559 (24.7) .972 (5.3) .209 (3.5) .138 (5.0) .197 m12 p1 (1.0) x (2.0) ty p .039 x .079 (0.2) ty p .008 (1.8) ty p .071 latchdown position (1.4) .055 63 52 1 4 l l com (4.9) .193 (1.8) .071 keyway (.127) .005 (5.08) .200 (9.0) .354 (1.7) ty p .067
series kb miniature pushbuttons www.nkk.com d31 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt typical switch dimensions single & double pole square ? snap-in mount single & double pole rectangular ? snap-in mount single & double pole round ? snap-in mount single pole models do not have terminals 4, 5, & 6. kb16kkw01-05-cb single pole models do not have terminals 4, 5, & 6. kb26mkw01-05-cb single pole models do not have terminals 4, 5, & 6. kb16nkw01-05-cb (2.3) .090 (11.6) sq .457 (14.0) sq .551 (1.0) .039 (24.7) .972 (5.3) .209 (5.0) .197 (1.0) x (2.0) ty p .039 x .079 (0.2) ty p .008 (1.8) ty p .071 (3.5) .138 latchdown position (1.4) .055 63 52 1 4 l l com (4.9) .193 (1.8) .071 keyway (.127) .005 (5.08) .200 (9.0) .354 (1.7) ty p .067 63 52 1 4 l l com (4.9) .193 (1.8) .071 keyway (.127) .005 (5.08) .200 (9.0) .354 (1.7) ty p .067 (1.0) .039 (24.7) .972 (5.3) .209 (5.0) .197 (1.0) x (2.0) ty p .039 x .079 (0.2) ty p .008 (1.8) ty p .071 (3.5) .138 latchdown position (1.4) .055 (11.6) dia .457 (14.0) dia .551 (2.3) .090 (11.6) .457 (16.1) .634 (18.5) .728 (14.0) .551 (1.0) .039 (24.7) .972 (5.3) .209 (5.0) .197 (1.0) x (2.0) ty p .039 x .079 (0.2) ty p .008 (1.8) ty p .071 (3.5) .138 latchdown position (1.4) .055 63 52 1 4 l l com (4.9) .193 (1.8) .071 keyway (.127) .005 (5.08) .200 (9.0) .354 (1.7) ty p .067
series kb miniature pushbuttons www.nkk.com d32 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles typical switch dimensions square ? barrier ? bushing mount single & double pole rectangular ? barrier ? bushing mount single & double pole square ? barrier ? snap-in mount single & double pole kb15skw01b-6g-jb single pole models do not have terminals 4, 5, & 6. kb15kkw01b-5c-jc single pole models do not have terminals 4, 5, & 6. kb15rkw01b-5f-jf single pole models do not have terminals 4, 5, & 6. 63 52 1 4 l l com (4.9) .193 (1.8) .071 keyway (.127) .005 (5.08) .200 (9.0) .354 (1.7) ty p .067 63 52 1 4 l l com (4.9) .193 (1.8) .071 keyway (.127) .005 (5.08) .200 (9.0) .354 (1.7) ty p .067 63 52 1 4 l l com (4.9) .193 (1.8) .071 keyway (.127) .005 (5.08) .200 (9.0) .354 (1.7) ty p .067 63 52 1 4 l l com (4.9) .193 (1.8) .071 keyway (.127) .005 (5.08) .200 (9.0) .354 (1.7) ty p .067 rectangular ? barrier ? snap-in mount single & double pole kb15nkw01b-5d-jd single pole models do not have terminals 4, 5, & 6. (5.0) .197 (1.0) .039 (14.2) .559 (24.7) .972 (5.3) .209 (5.0) .197 m12 p1 (1.0) x (2.0) ty p .039 x .079 (0.2) ty p .008 (1.8) ty p .071 (8.8) .346 (11.6) sq .457 (14.0) sq .551 (11.6) sq .457 (14.0) sq .551 (1.0) .039 (24.7) .972 (5.0) .197 (1.0) x (2.0) ty p .039 x .079 (0.2) ty p .008 (1.8) ty p .071 (5.3) .209 (8.8) .346 (11.6) .457 (16.1) .634 (18.5) .728 (14.0) .551 (5.0) .197 (1.0) .039 (14.2) .559 (24.7) .972 (5.3) .209 (5.0) .197 m12 p1 (1.0) x (2.0) ty p .039 x .079 (0.2) ty p .008 (1.8) ty p .071 (8.8) .346 (11.6) .457 (16.1) .634 (18.5) .728 (14.0) .551 (1.0) .039 (24.7) .972 (5.0) .197 (1.0) x (2.0) ty p .039 x .079 (0.2) ty p .008 (1.8) ty p .071 (5.3) .209 (8.8) .346
series kb miniature pushbuttons www.nkk.com d33 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt optional accessories pcb adaptors dust covers at701 single pole straight pc terminals at702 double pole straight pc terminals material: glass fber reinforced polyamide note: order adaptors separately + - 6 5 41 2 3 nc com no (0.2) ty p .008 (2.54) ty p .100 (10.16) .400 (2.54) ty p .100 (0.2) ty p .008 keyway (12.0) dia .472 switch depth (2.8) .110 (0.3) .012 (9.8) .386 (3.1) .122 (0.6) ty p .024 + - 6 5 41 2 3 nc com no (0.2) ty p .008 (2.54) ty p .100 (10.16) .400 (2.54) ty p .100 (0.2) ty p .008 keyway (12.0) dia .472 switch depth (2.8) .110 (0.3) .012 (9.8) .386 (3.1) .122 (0.6) ty p .024 3n c 1 2c om (2.54) ty p .100 (2.54) ty p .100 (0.8) dia ty p .031 (10.16) .400 no 3n c 1 2c om (2.54) ty p .100 (2.54) ty p .100 (0.8) dia ty p .031 (10.16) .400 no 6 5 4 material: lid: pvc pvc loses pliability below 0c (32f). base: polyamide panel thickness range: .020 ~ .268 (0.5 ~ 6.8mm) for bushing mounting; .020 ~ .079 (0.5 ~ 2.0mm) for snap-in mounting dust covers reduce the depth of switch behind panel by .047 (1.2mm). at495 for square & round (not for barrier type) at4025 for rectangular (not for barrier type) (12.3) dia .484 (5.1) .201 (21.0) sq .827 (7.0) .276 (1.2) r .047 (1.6) .063 (25.4) 1.004 (1.2) r .047 (21.0) .827 (12.3) dia .484 (7.0) .276 (11.8) .465 assembled cap height (13.0) sq .512 (6.5) .256 assembled cap height (13.0) sq .512 (6.5) .256 (11.8) .465
series kb miniature pushbuttons www.nkk.com d34 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable rockers touch tilt toggles indentation long ta b notch slot round ta b cap optional accessories protective guards at494 for square & round (not for barrier type) material: cover: polycarbonate base: polyamide at4024 for rectangular (not for barrier type) assembly instructions panel thickness range: .020 ~ .268 (0.5 ~ 6.8mm) for bushing mounting .020 ~ .091 (0.5 ~ 2.3mm) for snap-in mounting protective guards reduce the depth of switch behind panel by .047 (1.2mm). (6.5) .256 (11.5) .453 assembled cap height (5.1) .201 (12.3) dia .484 (9.0) .354 (19.0) sq .748 (7.0) .276 (1.2) r .047 (1.6) .063 (6.5) .256 (11.5) .453 assembled cap height (23.5) .925 (9.0) .354 (12.3) dia .484 (7.0) .276 (1.2) r .047 (19.0) .748 cap removal & installation for alternate action models cap must be in up position for cap removal. indentations on opposite sides of the cap provide an easy way to lift the cap out of the holder, using either the fnger nails, or cap extractor at109. led polarity & orientation in lamp socket cap replacement note that the cap has a pair of round tabs and a pair of long tabs which should be used for correctly replacing the cap in its holder. using the long tabs as guides, slide the cap with the long tabs moving into the slots on opposite sides of the cap holder. then, the round tabs will snap into notches on the other two sides of the holder. at108 socket wrench for bushing mounting at109 cap extractor at111 lamping tool super bright leds at625, at631, & at632 are electrostatic sensitive. led at635 leds at625 at631 at632 led at634 overtightening the mounting nut may damage the switch housing. flat (-) (+) flat (-) (+) (+) marking positive lamp socket negative lamp socket to p view of switch flat (+) (-) a ttention electrostatic sensitive devices
series kb miniature pushbuttons www.nkk.com d35 indicators accessories supplement tactiles keylocks rotaries pushbuttons d illuminated pb slides programmable toggles rockers touch tilt legends shaded areas are printable areas. shaded areas are printable areas. recommended print method: laser print film insert: clear polyester, 4 mil max. thickness suggested printable area for kb lens suggested printable area for film insert (10.08) sq .397 (11.6) sq .457 (0.76) ty p .030 (10.08) dia .397 (11.6) dia .457 (0.76) ty p .030 (14.58) .574 (16.1) .634 (0.76) ty p .030 (10.08) .397 (11.6) .457 (0.76)t yp .030 (12.98) .511 (14.5) .571 (0.76) ty p .030 (8.48) .334 (10.0) .394 (0.76) ty p .030 (8.48) dia .334 (10.0) dia .394 (0.76) ty p .030 (8.48) sq .334 (10.0) sq .394 (0.76) ty p .030 cap base filter or dif fuser film insert lens on st ar t recommended methods: screen print or pad print on lens. epoxy based ink is recommended. nkk switches can provide custom legends for caps . contact factory for more information.

▲Up To Search▲

Price & Availability of KB15CKW01-12-FF

	To Download KB15CKW01-12-FF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .